Canada's largest manufacturer of health & safety tags and vinyl products · Made in Canada since 1974
sales@canaltabindery.com
Can Alta Bindery & Graphics
0
GUIDE · SPECIFYING

Index tabs, properly specified.

Updated August 2026·7 min read·Written in our Canadian plant

Can Alta is Canada’s largest manufacturer of vinyl products, from binders to diploma holders. Tabs are the cheapest part of a document set and the first part to fail. Once the tab is gone, the organising system is gone with it — which makes the specification worth five minutes of attention rather than being left to whatever the supplier defaults to.

Banks and cuts: the arithmetic

A bank is one complete cycle of tab positions down the edge of the page. A 5-bank set has five tabs stepping from top to bottom, then the sixth tab starts a new bank back at the top. “Cut” is the same idea from the other direction: a 1/5 cut tab occupies one fifth of the usable edge.

The width follows directly. On a letter-size set, the usable tab edge is 10 inches, so tab width is 10 divided by the bank. A 5-bank gives 2″ tabs; an 8-bank gives 1.25″; a 10-bank gives 1″. That is why high-bank sets have such narrow tabs, and why there is a limit to how many positions are useful.

Note it is 10 inches, not 11. You will see the arithmetic done against the full page height, which gives wrong numbers and is a reliable sign that whoever wrote the page has not made tabs.

The letter tab sheet itself is 9″ x 11″ — wider than the page it sits behind, which is exactly the point: the tab extends past the sheet edge so it can be seen and grabbed.

Choosing your bank

Fewer, wider tabs are easier to read and much harder to tear. More, narrower tabs let you index finer. The trade is real, and it should be decided by the length of your longest tab title:

  • 5-bank (2″ tabs) — comfortable for real words. The default for most document sets, and the right choice when titles are phrases rather than numbers.
  • 8-bank (1.25″ tabs) — fits short words or numbers. Common in safety programs indexed by element number.
  • 10-bank (1″ tabs) — numbers and abbreviations only. Do not plan to fit “Emergency Response” on a 1″ tab.

If your titles do not fit the bank you want, you have three options: shorten the titles, drop to a lower bank and use more banks, or print vertically. In our experience shortening the titles is almost always the right answer, because a tab title that has been shrunk to 5 pt to fit is not readable from across a desk anyway.

Stocks

Two stocks cover almost everything:

90 lb index — the economy stock. Fine for reference sets that get opened occasionally, or for sets you expect to reprint annually anyway.

110 lb index — the heavy-duty stock. Noticeably stiffer, and the one to specify for anything opened daily or living in the field. On a three-year certification cycle the difference in cost is trivial against the cost of re-tabbing.

For heavier-duty applications still, tabs can be made from plastic rather than card, which is effectively indestructible and worth considering where the same set has to survive years of daily handling in a shop or a truck.

Mylar: what it is and when it earns its keep

Mylar is a trade name for biaxially-oriented polyethylene terephthalate — BoPET, a tough clear polyester film. In tab manufacture it is applied over the tab extension, wrapping the edge that sticks out past the page.

That extension is the entire failure point of a tab set. It is the part fingers grab, the part that catches, the part that creases and eventually tears off. A card tab that gets used daily will lose its tabs within months. Mylar reinforcement wraps the vulnerable edge in film and effectively ends the problem.

The rule we give customers: if the binder is opened weekly or more often, or if it goes into the field, specify Mylar. If it sits on a shelf and gets consulted a few times a year, plain card is fine. The cost difference is small; the difference in service life is not.

Practical details worth getting right

Collated and ready. Order tab sets collated in binder order so somebody is not sorting them by hand at the point of assembly. It costs nothing and saves real time on a large build.

Print both sides of the tab. A tab printed on one side only is invisible from half the directions it will be approached from. Two-sided printing is standard on our sets for exactly this reason.

Punch to match the binder. Three-hole is the default, but confirm it against the mechanism you are actually using. Tabs punched wrong are tabs thrown away.

Order spares. Titles change, sections get added, and a partial reorder later costs far more per unit than including extras in the original run, because setup does not scale down. Order the extra sets now.

Tab specification reference

Tab width arithmetic
Letter size: usable tab edge is 10″, so tab width = 10″ ÷ bank
5-bank
2″ tabs — comfortable for full words
8-bank
1.25″ tabs — short words and numbers
10-bank
1″ tabs — numbers and abbreviations only
Letter tab sheet
9″ x 11″ — wider than the page so the tab is visible and grabbable
Stocks
90 lb index (economy) · 110 lb index (heavy duty) · plastic for extreme service
Mylar
BoPET film wrapped over the tab extension. Specify it for anything opened weekly or used in the field.
COMMON QUESTIONS

Answered, briefly.

How wide is a tab on a 5-bank set?

Two inches. On letter size the usable tab edge is 10 inches, so tab width is 10 divided by the bank — 5-bank gives 2″, 8-bank gives 1.25″, 10-bank gives 1″.

What size is a letter index tab sheet?

Nine inches by eleven. It is wider than the page it files behind, which is the point — the tab extension projects past the sheet edge so it can be seen and grabbed.

What is Mylar reinforcement on a tab?

Mylar is a trade name for BoPET, a tough clear polyester film. On tabs it wraps the projecting tab extension — the part that fingers grab and that eventually tears off. It is worth specifying on any binder opened weekly or more, or on anything used in the field.

What stock should index tabs be printed on?

90 lb index is the economy stock and is fine for sets consulted occasionally. 110 lb index is the heavy-duty stock and is the right choice for daily or field use. Plastic tabs are available where a set has to survive years of constant handling.

How many tabs can I have in a set?

As many as you like — sets run in multiple banks. The practical limit is title length, not tab count: past a 10-bank the tabs are only 1″ wide and will hold numbers or abbreviations, not words.

Can you print custom index tabs in Alberta?

Yes. Custom tab sets are made to your artwork in our Canadian plant, printed both sides, collated in binder order, with optional Mylar reinforcement. Standard production is 7 to 10 working days from artwork approval.

STILL DECIDING?

Talk to the people who make it.

We have manufactured in Canada since 1974. Tell us the application and we will specify it properly — including telling you when the cheaper option is the right one.

Request a quote780.466.9973 · Monday to Friday, 8:00 to 4:30
DISTRIBUTOR PROGRAM

Distributors: sell it as your own.

Blind drop-shipping under your label, distributor pricing that protects your margin, and a factory that answers the phone. Apply for a trade account in two minutes.

Become a distributor