Canada's largest manufacturer of health & safety tags and vinyl products · Made in Canada since 1974
sales@canaltabindery.com
Can Alta Bindery & Graphics
0
GUIDE · DIPLOMA COVERS

Sizing a diploma or certificate holder.

Updated August 2026·6 min read·Written in our Canadian plant

Can Alta is Canada’s largest manufacturer of vinyl products, from binders to diploma holders. Almost every ordering mistake on diploma covers is the same one: someone orders a cover in the size of the certificate. A cover has to be bigger than what goes in it, and the amount bigger is not a matter of taste — it is what lets the document sit inside the corners without buckling. Get that one conversion right and the rest of the order is straightforward.

The conversion, which is the whole guide

Take the certificate’s dimensions and add 1/2″ to each overall dimension to get the finished closed size of the cover. So a standard 8 1/2″ x 11″ certificate goes into a 9″ x 11 1/2″ cover. A 8″ x 10″ certificate goes into a 8 1/2″ x 10 1/2″ cover, and so on.

That margin is not decorative. The document is held by corner slits or corner mounts, and those corners need material to sit in. Order a cover the same size as the certificate and either the document will not go in at all, or it will go in bowed and stay bowed.

Which leads to the rule we give every customer: measure the actual certificate, do not assume the size. Diplomas trimmed by a print shop drift from nominal, and older institutional certificates in particular turn up at sizes that were standard once and are not now. A five-second measurement prevents a reprint.

Portrait, landscape, and telling us which

Covers are made in both orientations and they are not interchangeable — the corners, the opening and any imprint are all placed for one or the other. When you specify a size, specify it in the order the document reads: 9″ x 11 1/2″ is a portrait cover, 11 1/2″ x 9″ is a landscape one.

If the certificate is landscape and the cover is portrait, nothing on the order is technically wrong and everything about the result is. It is worth one extra sentence on the purchase order.

Single panel, double panel, and what each is for

A single-panel holder is one leaf with corners on the inside face. It presents a single document and is the economical choice for volume — graduation, certification, membership.

A double-panel holder opens like a book, with a document on each side or a document facing a printed page. Use it when there are two things to show: a diploma and a transcript, a certificate and a letter, an award and a citation.

The other structural choice is padding. A padded cover has a soft layer under the outer material, which gives it the substantial hand people associate with a serious credential. An unpadded cover is flatter, thinner, cheaper, and easier to mail in quantity. Neither is better; they are for different occasions and different budgets.

Corners, ribbons and how the document is held

Most covers hold the document with corner slits cut into the lining, which the four corners of the certificate slide behind. It is clean, invisible from the front, and it does not mark the document.

A ribbon across the inside corners is the traditional alternative and reads as more ceremonial. Ribbons can be matched to institutional colours, which is why schools and associations tend to choose them.

A few practical notes. Corner slits are sized for a normal certificate stock, so an unusually heavy or mounted document should be flagged at quote time. And if the certificate will be removed and reinserted frequently — a licence renewed annually, say — say so, because that is a different wear pattern than a diploma that goes in once.

Materials and imprint

Diploma covers are made in vinyl and leatherette, in a range of grains and colours. Leatherette carries a grain and a hand that reads as more formal; smooth vinyl is cleaner and more modern. Colour is the main institutional decision — most organisations match theirs and keep it consistent for decades, which is a good argument for choosing a colour the supplier will still stock in ten years.

Decoration is almost always foil stamping or blind debossing. Foil presses coloured foil into the material — gold and silver being the traditional choices — and gives a bright, formal mark. Blind debossing presses the same die without foil, leaving a tonal impression in the material itself. It is more restrained and, in our experience, ages better than a foil that has begun to wear.

Both methods use a metal die made from your artwork, which means clean vector art matters and very fine detail does not survive well. There is more on that in our guide to decoration methods.

Ordering for an event that repeats

Convocations, certification ceremonies and annual awards come round again. Two things worth doing on the first order: buy enough to cover the next cycle, since setup cost does not scale down and a small reorder is disproportionately expensive per unit; and make sure the supplier keeps your die and artwork on file so the reorder is a phone call, not a fresh prepress job.

We manufacture diploma and certificate covers in our Canadian plant, keep artwork and dies on file indefinitely, and send a free electronic proof on every order including reorders.

Certificate size to cover size

The rule
Add 1/2″ to each overall dimension of the certificate.
8 1/2" x 11" document
9″ x 11 1/2″ cover
8" x 10" document
8 1/2″ x 10 1/2″ cover
Orientation
Quote the size in reading order — 9″ x 11 1/2″ is portrait, 11 1/2″ x 9″ is landscape. They are not interchangeable.
Before you order
Measure the actual certificate. Trimmed and legacy documents drift from nominal sizes.
Panels
Single panel for one document · double panel to face two documents, or a document and a printed page.
Holding method
Corner slits (clean, invisible) or corner ribbons (ceremonial, colour-matchable).
Decoration
Foil stamping or blind debossing, both from a metal die made to your artwork.
COMMON QUESTIONS

Answered, briefly.

What size diploma cover do I need for an 8.5 x 11 certificate?

A 9″ x 11 1/2″ cover. The rule is to add 1/2″ to each overall dimension of the document, which gives the corners something to hold and stops the certificate buckling inside the cover.

Why is the cover bigger than the certificate?

Because the document is held by corner slits or corner mounts, and those corners need material to sit behind. A cover cut to the same size as the certificate either will not accept it or will hold it bowed.

What is the difference between a single-panel and a double-panel holder?

A single panel is one leaf with corners on the inside face and presents one document — the economical choice for volume. A double panel opens like a book and holds a document on each side, which is what you want when a diploma is paired with a transcript, or a certificate with a letter.

Should I choose foil stamping or blind debossing?

Foil presses coloured foil — usually gold or silver — into the material for a bright, formal mark. Blind debossing presses the same die without foil, leaving a tonal impression in the material. Foil reads as more ceremonial; blind deboss is more restrained and tends to age better as the cover wears.

Can I get diploma covers in my institution's colour?

Yes. Covers are made in vinyl and leatherette across a range of grains and colours, and ribbons can be matched as well. Because institutions keep the same colour for decades, it is worth choosing one your supplier will still be stocking in ten years.

Do you make diploma covers in Alberta?

Yes — we manufacture diploma and certificate covers in our own Canadian plant and have done since 1974. Artwork and stamping dies are kept on file indefinitely so reorders for the next convocation do not repeat the setup work.

STILL DECIDING?

Talk to the people who make it.

We have manufactured in Canada since 1974. Tell us the application and we will specify it properly — including telling you when the cheaper option is the right one.

Request a quote780.466.9973 · Monday to Friday, 8:00 to 4:30
DISTRIBUTOR PROGRAM

Distributors: sell it as your own.

Blind drop-shipping under your label, distributor pricing that protects your margin, and a factory that answers the phone. Apply for a trade account in two minutes.

Become a distributor