Sizing a card or badge holder properly.
There is an international standard for the size of an ID card, which means most card holder decisions are already made for you. The ones that are not — thickness, orientation, material and how the badge attaches — are where orders go wrong, and thickness is the one that catches almost everybody.
The card size is standardised
Credit cards, drivers licences, employee ID cards and most access cards all share one format: ID-1, defined by ISO/IEC 7810. It measures 85.60 mm x 53.98 mm — near enough 3 3/8″ x 2 1/8″ in the units the trade actually quotes in — with a nominal thickness of 0.76 mm.
That is why a standard badge holder fits your bank card and your work pass equally well. If your card came out of a normal card printer, it is ID-1 and a standard holder will fit it.
Which makes the real question a different one: is your card actually a standard card?
The thickness problem
Access cards are frequently not 0.76 mm. A clamshell proximity card — the thick, slightly bowed white card common in older access systems — houses an antenna and a chip inside a moulded shell, and runs to roughly twice the thickness of a standard card. It has the same footprint, so it looks like it should fit, and then it does not go into the holder, or it goes in and cannot come out.
This is far and away the most common badge holder ordering error we see. The fix is trivial if you catch it beforehand: measure the thickness of an actual card before ordering, and if it is materially thicker than a bank card, say so at quote time so we supply a holder built for it.
Thickness also stacks. A card in a holder that is also carrying a second card, a paper insert, or a fold-over flap needs room for all of it. Tell us what is going in, not just what the main card is.
Orientation, and why it is not just a preference
Holders are made portrait (vertical) and landscape (horizontal), and the two differ in more than shape: the opening, the slot or hole position, and any printed area are all placed for one orientation.
Match the holder to how the card is printed and to how it will be read. A portrait card in a landscape holder is upside-down or sideways to anyone looking at it. If badges are read at an access reader, also consider which way the card has to face — a swivel attachment solves most of the twisting problems that come with a long day of wear.
Rigid, flexible, and what each protects against
Rigid holders — moulded, hard-shell — protect the card from bending and are what you want where a badge is worn all day in a physical job. They are the more durable choice and they keep a card flat, which matters for cards with an embedded antenna, since repeated flexing is what eventually kills a prox card.
Flexible vinyl holders are softer, quieter, lighter and considerably cheaper. They suit office environments, visitors, events and conferences, and they are the right answer when the badge does not need to survive a shift on a site.
One property worth asking about is print protection. Some card printing transfers ink to the inside of a soft vinyl holder over time, particularly with heat, and the badge comes out faded with a ghost of itself on the plastic. Holders made with an anti-print-transfer lining exist specifically for this, and are worth specifying where badges are printed in-house and worn for years.
How the badge attaches
The attachment method needs to be settled at the same time as the holder, because it determines whether the holder needs a slot, a hole, or neither.
- Lanyard — the holder needs a slot or a hole. Best where the badge is presented to a reader or read by people at a distance. See our lanyard buying guide for widths, lengths and attachments.
- Badge reel — a retractable cord, so the badge can be pulled to a reader and released. The obvious choice where readers are awkwardly placed.
- Clip or pin — a bulldog clip or a pin-back, worn on a pocket or a lapel. Discreet, and it keeps the badge clear of moving equipment.
If you are ordering plain cards that have not been slot-punched, flag it — a card with no hole and no holder cannot be attached to anything, and that discovery normally happens on the morning of an event.
What we will not guess at
We publish the ID-1 card dimensions above because they come from a published international standard. We will not publish a table of slot-punch dimensions or holder cut-out sizes, because those vary by manufacturer and we have not verified a set we would stand behind. If you need a holder to accept a specific card and a specific attachment, send us the card — or the exact card model — and we will confirm the fit rather than estimate it.
Card and holder reference
- Standard card format
- ID-1, defined by ISO/IEC 7810
- Dimensions
- 85.60 mm x 53.98 mm — approximately 3 3/8″ x 2 1/8″
- Nominal thickness
- 0.76 mm
- Clamshell prox cards
- Same footprint, roughly twice the thickness. They do not fit standard holders — measure before ordering.
- Orientation
- Portrait and landscape holders differ in opening, slot position and print area. They are not interchangeable.
- Rigid holders
- Protect against bending and keep antenna cards flat. For all-day wear in physical work.
- Flexible vinyl
- Lighter, quieter, cheaper. For offices, visitors and events. Ask about anti-print-transfer lining.
- Attachment
- Lanyard (needs a slot or hole) · badge reel · clip or pin
Answered, briefly.
What is the standard ID card size?
The ID-1 format defined by ISO/IEC 7810: 85.60 mm x 53.98 mm, or approximately 3 3/8″ x 2 1/8″, with a nominal thickness of 0.76 mm. It is the same format as a credit card, which is why standard badge holders fit both.
Why will my proximity card not fit a standard badge holder?
Because it is almost certainly a clamshell card. Those have the same footprint as a standard card but run to roughly twice the thickness, since the antenna and chip sit inside a moulded shell. Measure the card’s thickness before ordering and specify a holder built for it.
How thick is a clamshell proximity card?
Meaningfully thicker than the 0.76 mm nominal of a standard ID-1 card — roughly double. Because thicknesses vary between manufacturers, the reliable approach is to measure the card you actually have, or send us the card model, rather than order against an assumed figure.
Should I choose a rigid or a flexible badge holder?
Rigid holders protect the card from bending and keep an antenna card flat, which is what you want for all-day wear in physical work. Flexible vinyl is lighter, quieter and cheaper, and is the sensible choice for offices, visitors and events.
What causes badge printing to fade inside a holder?
Print transfer — ink from the card migrating onto the inside of a soft vinyl holder over time, especially with heat. Holders made with an anti-print-transfer lining are made to prevent it, and they are worth specifying where badges are printed in-house and worn for years.
Do I need a portrait or landscape holder?
Match the holder to how the card is printed and read, because the opening, slot position and print area are all placed for one orientation. A portrait card in a landscape holder reads sideways to everyone looking at it.
Talk to the people who make it.
We have manufactured in Canada since 1974. Tell us the application and we will specify it properly — including telling you when the cheaper option is the right one.